2010 Suzuki SX4 Keyless Entry Remote Fob Smart Key Programming Instructions

Instructions

How to Program a 2010 Suzuki SX4 Keyless Entry Remote Fob Smart Key

Step by Step How to Programming Instructions:
 
Use these instructions if you have the separate key and remote system. 

1. Remove key from ignition switch.

2. Close all doors.

3. Open drivers door

4. Insert key and turn to ON position and within 10 seconds turn key off and remove key.

5. Within 20 seconds Close and open drivers door 3 times.

6. Insert key and turn to ON position and within 10 seconds turn key off and remove key.

7. Locks should now lock and unlock automatically to confirm you have entered programming mode.

8.  Press the UNLOCK button on remote and locks should cycle to confirm programming.

9. Repeat step 8 on each additional remote.

10. Exit vehicle with keys and remote, close door test remote(s).

 
 
Step by Step How to Programming Instructions:
 
Use these instructions if you have Smart Key System.
 NOTE:
• You can program up to four remote controller codes into your vehicle’s memory. The four codes may be the same or different.
• If you try to program a fifth code, the four remote controller codes that are programmed will be cleared automatically.
• If you program a new remote controller code, all of the old remote controller codes that are in your vehicle’s memory will be erased automatically. When you program a new remote controller, you should reprogram any additional remote controllers at the same time.
• Before you begin programming, have all of your remote controllers available.
 
1. Close all the doors of the vehicle.
 
2. Sit in the driver’s seat and confirm that the driver’s door is unlocked.
 
3. Insert the key into the ignition switch.
 
4. Complete steps 1 through 6 described below within 25 seconds after step 3). 
 
   A) Push the power door locking switch of the driver’s door to the lock position and then push it to the unlock position.
 
   B) Repeat step 1 two more times.
 
   C) Push the power door locking switch of the driver’s door to the lock position.
 
   D) Remove the key from the ignition switch and then insert it again.
 
   E) Repeat step 4 three more times.
 
   F) To start the engine, turn the ignition switch to the “START” position. Wait for 3 seconds.
 
   G) Proceed to step 5) within 60 seconds after the engine has started. 
 
NOTE: You cannot program the remote controller if you don’t complete steps 1 through 6 within 25 seconds. You cannot program the remote controller if you do not proceed to step 5) within 60 seconds after the engine has started.
 
5. Turn the ignition switch to the “LOCK” position. A buzzer will sound twice and the door lock switch will be activated from the lock position to the unlock position automatically.
 
6. Press the “LOCK”, “UNLOCK” or “PANIC” button on the remote controller. A buzzer will sound twice and the door lock switch will be activated from the lock position to the unlock position automatically. If you want to program an additional remote controller, repeat the procedure of step 6) using the additional remote controller. NOTE: Complete step 6) within 30 seconds. You can program up to four remote controllers.  
 
7. To complete programming, remove the key from the ignition switch or turn the ignition switch to the “ON” position.
 
8. Make sure that the keyless start system and keyless entry system operate properly by operating each remote controller. If you cannot operate the keyless start system and/or keyless entry system, repeat this programming procedure again. 
 
To change the old remote controller codes in your vehicle’s memory If you have lost one of the remote controllers, you should change the remote controller codes in your vehicle’s memory as soon as possible for security. To erase the remote controller code(s) in your vehicle’s memory, you should program the new remote controller code. The old codes in your vehicle’s memory will be erased automatically. If you have more remote controller(s), you must program all of the remote controller codes at the same time. You cannot operate the keyless start system and keyless entry system using any remote controller that is not programmed at the same time. 
 
 
 
Call (877) 675-1507 to find a Locksmith in your area.